Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Arganine

  1. Arganine

    DTA301 and DCH not establishing

    Hi, thank you for all the help I have received so far WWDT: I am not aware of there being anything set up specifically for data bignose21: I completely tore down what I had set up and started again. I created a new customer also in ld 15 as I wanted to make sure that I did not use any of the...
  2. Arganine

    DTA301 and DCH not establishing

    Hi Bignose We turned the CRC4 off on the server end as we realised that was giving us CRC errors and the remote alarm. Can I ask what it is that indicates that the DCH 31 has not connected, is it the AEST message? The reason I ask is that I was informed elsewhere that the AEST meant Auto...
  3. Arganine

    DTA301 and DCH not establishing

    The 1st PRI card was preconfigured before I joined the company. The second PRI card I installed with the intention of steering calls to the Aculab card in our server.
  4. Arganine

    DTA301 and DCH not establishing

    Here are the print outs requested by Ace ld 60 DTI000 SL-1 --- SYS-12/AXE-10 SWE/NUMERIS/SWISS/TCNZ /EUROISDN/SING/THAI/MSIA/INDO/CHNA /INDI/PHLP CHANNEL TIMESLOT MAPPING . SL-1 NETWORK TIMESLOT B-CHANNEL 1 -15 1 -15...
  5. Arganine

    DTA301 and DCH not establishing

    So why not just ask me to supply that information in the 1st place. As you state, you have decades of experience, where as I do not. As for getting my 'panties in a wad' just how old are you. I have stated previously that I have no experience in Meridians and all I have 'learned' is what I...
  6. Arganine

    DTA301 and DCH not establishing

    Ace I do hope that you are not trying to be awkward or insulting as that is how I have found your post to be. I 'care' how a TN is formed because I am confused about the numbers that I currently have on the meridian, and what I need to do to get a call through the new card and to the Aculab in...
  7. Arganine

    DTA301 and DCH not establishing

    Thanks John. Ok so could you explain to me how a TN is formed, and what do I need to do to get calls handled by the new PRI card I have installed. This is the card on loop 3. I have a DCH of 31 on 31, a tie on ch1 and did on ch2.
  8. Arganine

    Cisco 501 and BT Hub

    Can you put a dump of your config non here please.
  9. Arganine

    need help with PRI T1

    ENCH 34 8 in ld 60
  10. Arganine

    DTA301 and DCH not establishing

    LOL bignose21, I've only been doing THIS meridian switch for 3 weeks, and I'm making it all up as I go along. Sorry if I appear to be confusing anyone, I may not be describing things in the right way, or, more than likely, I have done it completely wrong and therfore what I describe is wrong...
  11. Arganine

    DTA301 and DCH not establishing

    Thanks for the help. I wonder, could someone explain how TN numbers are made up. I am trying to move a DN number from an existing pri card to my new pri card The existing card is on loop 1, my new card is loop 3. the TN for the number is current 2 9, to move it to my new card I can only use...
  12. Arganine

    DTA301 and DCH not establishing

    Hi New to the forum and new to Switches. I have enabled dch 31, yet when I stat it it says AEST rather than EST, and I am getting regular DTA301 messages, are the two linkee, and can I do anything about it?
See more

Part and Inventory Search

Back
Top