Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by ableseaman

  1. ableseaman

    Hunt Group

    Thanks for the response Nortel4Ever I tested the setup you described yesterday before posting, albeit with different timers (no answer timer=20s and voicemail timer=45s) With all 6 extensions within hunt group Extension 1 - 20 seconds Extension 2 - 20 seconds Extension 3 - 5 seconds voicemail...
  2. ableseaman

    Hunt Group

    Hello We are migrating from a CS1K to IP Office. We have a large number of hunt groups, both linear and RRB, with/without voicemail. We want to replicate the following example CS1K hunt group setup on the IPO Linear/Sequential hunt group 6 extensions within group, with option to opt in/out...
  3. ableseaman

    Pre-Translation or equivalent

    Will do. Cheers
  4. ableseaman

    Pre-Translation or equivalent

    Thanks for the quick response Firebird. Looking at the options, the system speed dial looks to be the easiest for oursleves to cover in-house and from the way you describe will defintley cover our requirement. We will give that a bash over the next few days. Cheers again.
  5. ableseaman

    Pre-Translation or equivalent

    Good Morning BCM400 Version 3.7 We have a requirement for an extension to be setup to allow access to a small number of external numbers only. Ideally this would follow the process of setting up the relevant external numbers to correspond to the keypad i.e. dial 1 for external number...
  6. ableseaman

    CS1000e Audit of IP Sets

    Thanks for the feedback from all. We do receive notifications of leavers but sometimes the associated position is placed on hold where the post may be filled at a later date and Sections want to hold onto the extension 'just in case'. In addition users move within our company and are then...
  7. ableseaman

    CS1000e Audit of IP Sets

    Good Afternoon Is there a way to establish when IP extensions were last used? We have historical issues with staff members leaving or moving on and their associated IP extension being left in circulation. In the past we have addressed this issue by requesting an up to date extension list from...
  8. ableseaman

    DHCP/LAN Switch Issue

    Sorry for taking so long to respond holdmusic32 Still haven't completley got to the bottom of this one but eventually installed a replacement 4550 switch with a lower code (matches the same code as the rest of the 4550 nodes on the LAN) and this has cured the issue. Suggests was either an issue...
  9. ableseaman

    DHCP/LAN Switch Issue

    Afternoon Bit longwinded this one........ We have an issue where IP sets on a ‘Secondary’ site won’t boot up – the set simply just continues to display ‘restarting’. 'Voice VLAN' (VLAN 2): 192.168.38.0/24 'Data VLAN 1'(VLAN 1): 192.168.8.0/24 'Data VLAN 2'(VLAN 5): 192.168.67.128/25 We have...
  10. ableseaman

    CS1000 CDR Set-UP

    Thanks both I have reported to our maintainer..........
  11. ableseaman

    CS1000 CDR Set-UP

    Minicompbx Print out of TTY shows; TTY 0 : ENBL TTY 1 : DSBL ( MGC 0 0 ) TTY 2 : DSBL ( MGC 0 0 ) TTY 3 : DSBL DES: PTY_1 TTY 4 : DSBL DES: PTY_2 TTY 5 : DSBL DES: PTY_3 TTY 6 : ENBL DES: PTY_4 TTY 7 : ENBL DES: ONSITE TTY 8 : ENBL ( MGC 4 0 ) TTY 9 : ENBL ( MGC 8 0...
  12. ableseaman

    CS1000 CDR Set-UP

    Cheers Firebird CDR printed off below. It doesn't mention anything specifically about MGCs within here just that it uses port 2. Does this mean that port 2 on both Cores MGC 0-0 & MGC 0-1 will cover CDR or does it need to be specifically setup for MGC 0-1 port 2? TYPE CDR_DATA CUST 00 CDR...
  13. ableseaman

    CS1000 CDR Set-UP

    Good Afternoon We have a CS1000E with Call Servers (MGC 0-0 & MGC 0-1) split between 2 locations - both of which are on the same Campus LAN. Our Call Logging system is connected to MGC 0-0 on port 2. We want to move our call logger to MGC 0-1. I have printed off the ADAN settings as thought...
  14. ableseaman

    5510 layer3 switch connectivity to 5520 layer 2 stack

    Afternoon We have an Avaya ERS5510 switch running with advanced routing software connecting to our managed WAN. We have a seperate Avaya ERS5520 stack (2 switches) so server a bank of servers. The 5520 has a single trunk port (switch 1 port 48) connecting back to the 5510 (Port 24). To add a...
  15. ableseaman

    Console 'Messaging' Query

    Hi Marc Thanks for all your help, this is making a lot more sense now. I will download a MIRAN guide and check the amount of channels we have (think it is 2) and see how I get on. Thanks for the further offer of assistance........... Cheers Again
See more

Part and Inventory Search

Back
Top