Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by 4wireguy

  1. 4wireguy

    Can't transfer a incoming ISIG transferred call

    Hey John, the DSC FLEN was at zero (0). I interpret that to mean it doesn't wait to send digits. Is that right? I did lower several timers hoping to 'speed up' the asup or whatever it is that provides a clear to transfer option. Sporty2, I found that patch, but it the description doesn't seem...
  2. 4wireguy

    Can't transfer a incoming ISIG transferred call

    Thanks John... I have been looking at timers, but never thought of FLEN. I was also would bet money a-sup was missing. I wish I knew how it gets passed along, but felt it most be the case. As far as steps, I suggested several options for doing this, all met with a polite, but dumb look. I will...
  3. 4wireguy

    Can't transfer a incoming ISIG transferred call

    Thanks in advance. I have a CS100M MG 4.5. Call flow looks like this: incoming DID call to ACD NCFW to CP; CP transfers to 6604 (NIT1) which is steered across PRI (ISIG) to Amtelco and operator; operator transfer to ACD NCFW to CP; CP transfer to 2616 or 3904. At arrival of the call it can not...
  4. 4wireguy

    Dead Air dialing out

    PerryPJ, I didn't set it up this way, but this is the way it is: Each trunk has its own route; I only showed the first two trunk routes, because this is the only ones experiencing the issue. As far as RLB the are like this: Local calls RLI 1, Toll-free RLI 2, LD RLI 3, Int'l RLI 4 and 911 is RLI...
  5. 4wireguy

    Dead Air dialing out

    I have CS1000e (rel 4.5) with the following issue: intermittently, when they dial local (10 digit plan), they get dead air... don't hear a reorder and the digits they continue to dial are not displayed. An occassional and explainable reorder sometimes occurs... ten phones sharing two analog (GS)...
  6. 4wireguy

    Symposium 5.0 to CCMA/CCMS 6.0 cut over

    John... see you on here a lot and must say, quite impressed with the help you provide. Its fun, isn't it. There is a twist to this install, my jaw hit the desk top... there isn't a single PC running the fat client on SCCS. I don't know of a way to deaquire sets/cdns at the server (do you?). I...
  7. 4wireguy

    Symposium 5.0 to CCMA/CCMS 6.0 cut over

    First off, thanks to you both. I will get a PC or two configured correctly prior to cut time; back up SCCS; power it down; install the new CC6 server; power it up; access CC6 via browser; activate the Master script and test. If it fails I have a 6 hour Nrius ticket created (the Nortel engineer...
  8. 4wireguy

    Symposium 5.0 to CCMA/CCMS 6.0 cut over

    This a server swap - System is MGC with CPPM call server and signaling server at 5.5. This is a Co-resident CCMS/CCMA (so license and utility server installed - no replication). Call Pilot is 4.0. I will be taking out the SCCS server and replacing with the 'new' CC6 server. The call server...
  9. 4wireguy

    Sig server IP programming problem

    I am in the process of upgrading to 5.5 and going to MGCs. The step I am in is programming Sig Servers. Is there a way to change the alternate NRS IP to 0.0.0.0, since we don't have an alternate NRS? You can't change it to 0.0.0.0, nor can you enter past it... so I have made it a valid, but...
  10. 4wireguy

    New to 3300 need help programming PRI

    MitelInMyBlood, It's new out of the box... a 3300 with the duo E1/T1 card. I can't tell you the SW since I am many miles away right now. Thanks, (old) 4WireGuy
  11. 4wireguy

    New to 3300 need help programming PRI

    I am scheduled for school, but really need to get a system installed prior. We have another system, which I took screen shots of the programming/configuration. What I need to know is the required order of programming, particularly involving setting up a 2 PRI trunk group. I am assuming there is...
  12. 4wireguy

    11C - ACD phones won't obey CFW

    GHTROUT and BigIndian, I apprecitate your responses. Problem solved. This morning I outed the SCNs on supervisor phones and made them AGT keys. Thanks again... Clint
  13. 4wireguy

    11C - ACD phones won't obey CFW

    I am setting up 2 queues in a 11C running Suc 3.0 and removing MCR keys. Phones are M2616s, a mix of newer NT2Ks and NT9Ks... both fail, but some phones forward properly. I have swapped with known good phones. They have identical CLS and set up. MARP is correct. DID and non-DID are keys 2 and 3...
  14. 4wireguy

    Changing IP address on Sun Box (VPS IVR)

    We are moving to a new location and I will need to change the IP address on our IVR system. Can anyone tell me the procedure or where to find it. Thanks!
  15. 4wireguy

    i2050 using VPN doesn't work while making a call

    I am implementing (or trying too) i2050 over a VPN connection with the old ITG-P and an old version of i2050 soft phone. Testing without VPN works great (corporate WAN). But, when I VPN in from home(Contivity client)... on an outbound call from the i2050 my speech (can't be heard) is completely...
See more

Part and Inventory Search

Back
Top