Smart questions
Smart answers
Smart people
Join Tek-Tips Forums

Member Login

Remember Me
Forgot Password?
Join Us!

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips now!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

Join Tek-Tips
*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.
Jobs from Indeed

Link To This Forum!

Partner Button
Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.
Just copy and paste the
code below into your site.

how to initiate md -computer connection via niu-ethernet cble

YAZICI (TechnicalUser) (OP)
22 Oct 02 8:52
I want to connect MD via tcp-ip .I have acable and connect NIU and one PCs ethernet card. But I cant do settings for winfiol 5.1 . How can i know what the md's ip adress. I gave my pc ip address. But i could not connect them. I will pleased to see your helps. Thanks you very much.....   
TBLuk (Vendor)
22 Oct 02 9:12

Here you go mate.

IONPP; Will check the current IP of the NIUs network port.

IONPC:EQU=1-0-10-60,IP=; Substitute the EQU and IP for your own values to set it up the way you need.
YAZICI (TechnicalUser) (OP)
23 Oct 02 3:17
Thanks. But I have to add that; we have no connection between Md and PC. Because our serial connection doesnt reply any command. I tried to ethernet TCP conn. I want to know does md has a known ip number at the assemble for all the systems. Thank you very much indeed.    ..YAZICI..  
TBLuk (Vendor)
23 Oct 02 4:00
I doubt it very much.

You would essentially need a serial connection to setup the TCP/IP connection.

We would be best to address the prloblem that you cannot access the MD110 with the serial connection.

When you connect the PC to the IPU/NIU, what are you doing? What is happening?
YAZICI (TechnicalUser) (OP)
23 Oct 02 5:24
At the setup menu;
Protocol: TCP/IP
host name: my ip address
port number :23
terminal type: unknown
target :md110
when I try to connect, program says connection failed and if I want to open properties to change.
also I want to attach this: My serial port connected to MD. But when I enter a comman , says command error.

I am trying to run program via using these two way. Thanks for your interests...     .........YAZICI......
TBLuk (Vendor)
23 Oct 02 8:56
As I said before, lets setup the serial connection first.

You are getting command error?

Please clarify.

What are you entering before it comes back with command error?
YAZICI (TechnicalUser) (OP)
23 Oct 02 9:08
Any command can make an error message. For ex: ALLREI; or GPDAP: GRP=ALL; makes error msg. I am really sorry to take your time, also thanks.
TBLuk (Vendor)
23 Oct 02 10:36
It's ok, I want to help.


It says "ENTER PASSWORD" and you enter the password and you are logged on.

What is the EXACT ERROR MESSAGE when you type GPDAP:GRP=ALL;

NOT ACCEPTED COMMAND BUSY? Etc etc, we need the message
YAZICI (TechnicalUser) (OP)
24 Oct 02 8:54
Dear TBluk;
When I echo sssssssssssss without ;i can login and system comes into niux type. But when i type sssss; system does not respond to my command. pass to other line and wait. then i try again but nothing occured. where is the problem. i connect terminal from COMII baud rate 9600 8 word lenght, no parity and 1 stop bit. also i use winfiol 5.1 . Have a nice day.  
TBLuk (Vendor)
24 Oct 02 9:13

You have inadvertantly logged into NIUX which is the file administration program for the NIU board.

When you are faced with the ?> prompt, type in quit in lower case, followed by ENTER

Then echo your SSSSSSSSSSSs again, and login as normal.

You wil now be able to issue commands again.

Let me know if this works
mduser (TechnicalUser)
24 Oct 02 9:58
To Yazici,

You said that you're able to login with SSSS without ';' to niux.

In niux you can use the 'netcnf e' command to see the IP settings of the NIU board. See Example below. Maybee it will help you. (If necessary you can change the IP parameters). For more commands in niux, type help.

  niux > netcnf e
  Current Ethernet setting:
  IP address     :
  Network mask   :
  Default router :
  Baud rate   :  65535 (0xffff)
  Data bits   :  255 (0xff)
  Parity      :  255 (0xff)
  Stop bit    :  255 (0xff)

   Any changes? (y)es or (n)o <no> y

  IP address (dec)
  New value:

  Subnet mask (dec)
  New value:

  Default gateway (dec)
  New value:

  Save current net config? (y)es or (n)o <no>n
YAZICI (TechnicalUser) (OP)
24 Oct 02 10:06
WOUUUUUUWWW. IT WORKS. Thank you  very very much. I can command to md now. I want to say a lot of thank sentences but my english not sufficent to state these words. At the and i am very pleased to meet you. Bye.... YAZICI...

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members!

Back To Forum

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close