INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Jobs

BCM50 LINE PROGRAMMING

BCM50 LINE PROGRAMMING

(OP)
Hi, I have a BCM50 R3. using isdn line 061 and 062 extn 221 will ring but all other sets will not. I have assigned
all installed sets with app & ring for line 061 and 062. can anyone please point me in the right direction
to get all installed sets to ring and answer

RE: BCM50 LINE PROGRAMMING

Well you say ISDN lines yet Lines 061 and 062 are for regular Analog lines...are you sure of what you have for lines from the carrier?

Some things to look at...

-Do feature * 0 and press the buttons on X221 to see what actual line numbers they are on the display
-Go into X221 and what lines are assigned
-Make sure when a call comes in those lines flash
-Go into lines and at the bottom under the Assigned DN's tab you will see what DN's are assigned and if A&P etc.

Otherwise if you are sure they are 061 and 062 you have programmed the other sets correctly.

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: BCM50 LINE PROGRAMMING

I think your lines might be ISDN2 (BRI). They are treated in the same way as analogue trunks as they both use lines 061 to 064 on the main BCM unit.

Assuming that you have BRI trunks, then you may need to configure target lines for each extension so that incoming DID (DDI) calls will ring the extension phone.

Usually the first extension (221) is set to receive all calls where DID calls can't get to any valid extensions.

Set up your target lines first, one target line per extension and then make sure that they are assigned.

Also look under the first tab in Element Manager to find out if your BCM is a BCM50 or a BCM50b system.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = http://somertel.com
linkedin

RE: BCM50 LINE PROGRAMMING

I assumed in that case then Lines 061-064 are on a first come fist serve basis?
i.e if you do not install 4 Internal Analog Trunk key codes but only installed a BRI module then the BRI lines will start at 061?



________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: BCM50 LINE PROGRAMMING

(OP)
Hi, the system is a BCM50B and i am using ISDN2 lines all phones show the linse rining but cannot answer

RE: BCM50 LINE PROGRAMMING

As per above you need to go into the reception set and see what lines are programmed using this method in Element Manager:
"Go into lines and at the bottom under the Assigned DN's tab you will see what DN's are assigned and if A&P etc."

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: BCM50 LINE PROGRAMMING

(OP)
Hi Curlycord, lines 061 and 062 show sets 221 - 227 app&ring and are a member of line pool A

RE: BCM50 LINE PROGRAMMING

Ok try going into Lines/TargetLines and look to see if any digits (such as part or all of you phone number/s) are entered under the Pub Received # column.

If there are high-lite that row then again look at the bottom for Assigned DN's.

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: BCM50 LINE PROGRAMMING

(OP)
Target line 125 has our number (339507) but no Assigned DN's

RE: BCM50 LINE PROGRAMMING

Sounds like it was not programmed and resorting to the "Prime Set" under "Target Line" 125

Remove lines 061 and 062 from all sets and assign Target Line 125 instead.
Note when you add a target line you can add as many appearances as required.
So if you have 4 channels (4 calls allowed on your circuit) then you can add 4 appearances of 125.
Normal only done on the reception set where the rest of the sets is Ring Only so that is comes in on the Intercom only.
You then Park calls and retrieve those parked calls from anywhere by Intercom 101 etc.


Note if you use Auto Attendant:
-that you must make sure Auto Attendants ring count under line 125 is shorter than the FNA ring count under each set or somebodies mailbox may answer the call after X rings.

Or just a mailbox answering:
-that the FNA ring count at each set is shorter than the FNA ring at receptions DN or somebodies mailbox may answer the call after X rings.


________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: BCM50 LINE PROGRAMMING

(OP)
Hi Curlycord,
all working now, thank you very much for all your help

Leigh

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members!

Resources

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close