INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Jobs

Mxone 6.1:PRI configuration

Mxone 6.1:PRI configuration

(OP)
Hi guys,

Basically I am new to mitel mxone series & documents on this is not too good. I have got one mitel system Rel 6.1 & done with configuration of analogue extension & few SIP extension.
Internal calling is working properly.

But don't know how to configure PRI with mxone system. We have check PRI line with service provider , the line working properly with their PRI line testing machine.
I have got pc-regen of mxone 5.0 & mxone 6.1 another system , it will great if someone help how to use this pc-regen to configure PRI line
a) How to check ISDN status like...L1 & L2 layer are sync with service provider.[show isdn status like is Cisco]
b)Then how can I check in Mitel mxone how many digit service provider is sending on PRI line.
c) DDI & DOD setting.

RE: Mxone 6.1:PRI configuration

Hi
Basic of rou is same with tsw/bcX so use rodai..rocai....roeqi...roddi... and nutri if needed.. for out and in use trace in pri rou


http://telfonika.blogfa.com

RE: Mxone 6.1:PRI configuration

(OP)
How can I check how many digits service provider is sending & also want to know commands to debug L1 & L2

RE: Mxone 6.1:PRI configuration

hi ,
to check the status for the trunks use the following command
susip:rou=x,tru=all;
this command before TSE6.3
new command
resource_status --externals --route-number x --trunk-number 1-1..1-x --traffic-status

to initiate DID
number_conversion_initiate -entry xxxx -conversiontype 0 -route y -pre z -numbertype 0 -truncate 4
where xxxx last for digits of PRI number , z : your internal number

RE: Mxone 6.1:PRI configuration

coolfalcon, did you read properly the question? Eric wants to trace the call, not checking the status. To trace the call is a totally different command....
Goes something like this: trace -lim -unit etc. in this case unit=slp60. The result can be printed out in different ways, so see you docs....

RE: Mxone 6.1:PRI configuration

fcpli , thank you for the note , and sorry for the misunderstanding .

there was old Ericsson tool called Signal Interpreter for SLP60 Signal trace , and now its built in and exist in the MTS.

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members!

Resources

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close