hi guys i am new to forum .. i hv a proble.. i am wrking in company wher i hv panasonic kx-td 100 pbx already deployed.. first problem is that i don't have the software of pbx and second is that we want to add more extension in it.. what is needed hardware or software.. plz help... it has alread 32 extension...

what cards are in the system? (will say on front of each one)

Do u hv a phn? Us it 2 call a dlr.

Try google upcmc for the software,
What pbx do you have?tda100 or tde100?

Ys eye concr wth crl!!

www.thetelephonemanonline.com

panasonic kx-tda 100

panasonic kx-tda 100
model: PSLP-1453
there are four cards..
LCOT 8
DHLC 8
DHLC 16
DHLC 16

can ny one explain these card.. i ma new to telphone exchanges...

TRhis took about 15 seconds on the internet. http://www.telavip.com.ve/manuales/Hybrid%20IP-PBX%20Installation%20Manual%20KX-TDA100%20KX-TDA200.pdf

CALL YOUR DEALER! You don't have enough skillz to work on the system yourself.

LkEErie

I think you need to master typing skills be for moving on to IT and Programming!!

www.thetelephonemanonline.com

guyz i hv master degree in computer science.. bt i dont familir with pbx just guide me i can do it.. plz...

How's that degree working out for you? Was some language involved in the degree? How did you make it through the degree program without knowing how to write formally or read a manual?

Pretend the TDA is a computer. You have an instruction set and it's IN THE MANUAL.

Now get going and don't bother to beg for "guidance" when you can't even help yourself.

or "urself" in your stupid shorthand txtspeak.

LkEErie

It must be an Elvis Masters Degree no one with a degree would type like a 2 year old??

www.thetelephonemanonline.com

i prob from the net and found that LCOT8 is trunk card. wch support 8 analog propetry lline.
and DHLC16 is digital hybrid line card wch support 16 extesion.. and now i want the software to connect the exchange to my laptop to add more DHLC16 card and manage it.. tell the procedure.. aad dont make fun guyz because "no one know everthing"..

The procedure is to get the manuals in your native language and read them or was knowing how to read not a requirement for your degree? and download the software from the dealer website in your country....

www.thetelephonemanonline.com

The problem with reading is in our country, there is no DHLC16. It's a DLC16 or DHLC8. DLC stands for DIGITAL LINE CARD and LCOT is Loop CO Trunk. The HYBRID line card only comes in 8 ports. I think that was in the very first section of the manual you must not have read.

Since you have that degree, you ought to be telling us how to install this stuff. I only went to Panasonic school and I was on the 9 year college plan without a degree......

LkEErie

First you don't need the console to wire an extension.Do the physical wiring first then come back with results to be guided on figuration having got the Maintenance console.

Remember you should be able to identify the free pairs from the DHLC 8 ,DHLC 16 ,DHLC 16 cards and choose where to terminate your additional extension.

If using a two pair or more,identify the extension number nearest to the point where you want to add an extension and borrow a pair if the point is far from thE PBX.

thnks to all i appricite your response... tell me when we add a extension card then we configure it throuh console aur its plug n pla...

You have provision for 24Digitals and 16Analogues according to the cards you listed.How many of which? do you have installed?I mean how many digitals do you have installed and how many analogues?What type (Digital or Analog?) do you want to add.

Your response is not clear to my previous question.Makes helping difficult.

Sorry 28Digitals 20Analogues

CARD ANALOGUES DIGITALS

DHLC 8 4 4

DHLC 16 8 8

DHLC 16 8 8

TOTAL 20 20


I SUPPOSE

all port aur full i want to add one more DLC16 card and configure it for a new block that is under construction..

So you have 40 extensions that are wired and are in use?

All I wonder is what is the part number of the DHLC16 card, as in the one that starts with TDA017x.

I see one for the NCP and a vaporware one for the Russian TDA, but you seem to think you have two of them.....

sorry they aur two card DLC16 one is LCOT8
and one is DHLC8
can i add more DLC16 card thats i want to confirm...

ye all extension are in use...

DLC16 * 2 has 32 Digitals Extensions
DHLC8 * has 4 & 4 Analogues

DLC16 is KX-TDA0172

YES YOU CAN ADD ONE MORE DLC16

thnks otoni54.. after ading the card i hv to configure it. i dont hve the console software can u hve it are snd me the link for

The software is normally with agents/dealers.Which country are you in?.Visit www.wanetelecoms.com i normally get from there.

Anything else?

The answer is yes, depending on the model of phone in use.

The DHLC has 8 digital and 8 analogue extensions on it plus 32 on the other 2 dlc16 cards

total is 40 digital and 8 analogue extensions

PSU? if medium then you have 128 points

points used is 8 for slts and 40 if using kxt76xx or DT xxx phones

If using Kxt 72xx, 74xx, they use 4 points each

if they all add up to less than 128 including extra card you are good to go.

you will be up to the limit for requiring a MEC card, do if you add and digital extra devices off the back of another digital phone (76xx and DT series only) you will have to get one of those as well.

Installing these is not rocket sience, but knowing how to terminate the cable in the correct order and how to program the system is what you need someone who is trained in telecommunication equippment for.

You tring to save a few bucks, could cost you a lot more in your time in the end... If it was a bomb would you go on line and ask strangers what wire to cut

he otoni i try the website bt it was nat free... is there any way to get it free from the internet.. bcoz the person before me in the company take the software with hem

Which country?

First do physical installation.

If you fail to get the software,you can program using PT

Here's the post that's probably going to get nuked, but here goes. This is the Tek Tips forum, not the we'll guide you every step of the way, even if you don't read the manual forum. You start the thread by saying you have 32 extensions. You tell us you have hardware that doesn't exist, and you can't seem to read a manual where all the information you seek is contained. If you had opened the link, you'd have found that there are SIX slots in a TDA-100 box, and either 64 or 128 points allowed in a small or medium power supply, the only ones that fit in a TDA-100 cabinet.

The descriptive names for the cards LCOT 8, DLC 16 and DHLC 8 stand for the number of ports on the card. The pinouts on the ports are fairly clear, first 8 pairs for the trunk card, first 16 pairs for the digital cards, and 8 times 3 pairs for the DHLC card is a Panasonic standard used in all systems since the KXT-123210 box. The point is, if you add up the numbers, you have a capacity for 40 digital and 8 single line extensions, and LOOK AT THE BOTTOM OF THE DIGITAL PHONE. Now plug a digital set into the XDP port and look at the display!

There is a set of manuals to a TDA system, the IM, FG, OM, PCPM, PTPM, and a couple more that don't apply (PPT and SD), along with the maintenance console that is required to program the system.

If you walked into your office tomorrow morning and the phone system had all red lights on the cards and an alarm, would you spend FIVE DAYS trying to fix it? I can walk into your office and add another DLC-16 and program it in less than 60 minutes, plus another 30 minutes to add the cable to the frame. With your demonstrated reading skills, I think you'd still be working on the Installation Manual after 90 minutes.

It all comes down to value. If your time is worth more than learning something badly, then call a professional to expand your system. If you want to pursue this stupidity, look to another forum for help, because this "good 'ol boy" is getting tired of this thread.

All this time wasted and all you had to do was read the linked manual given to you four days ago.....


LkEErie

dont be harsh dear.. i hv almost two month to cmplete the new blcok till than i am doing my home work.... and here forum are for help nt for the disgrace...frm discussion i hv get lot about pbx and i will do it myself.. and thnks for help.. all member.. i wil disturb u people more for help

Ishtaiqai,i agree with obtsystems.You may want to save afew bucks and end up paying more after messing up the system.Why not contact the person who installed your system.

It's alot cheaper than trying to fix it in which case you may mess it up and upon calling him,he takes the advantage to bill you more.

Companies normally keep records of guys who have installed their systems just incase they are needed.

You could learn from him as he does his work.

Best of luck.

me agree with u too bt i want to learn it by myself.. and i just need help of all u people..

I find that people that are so cheap that they think they can maintain there system have already annoyed the installer ... O I don't know about your installer but no one stands over my shoulder when I am programming except maybe my own tech .

www.thetelephonemanonline.com

He could use DXDP. Luckily no vowels are needed

at last i got the unified management console software 1 step completed

good luck reading the help files

www.thetelephonemanonline.com