INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Jobs

ssr2000

ssr2000

(OP)
Hi I want reset this switch to the factory settings. But I dont know how?

RE: ssr2000


Pulled from Enterasys - this needs local console access and will effectively remove the config too from memory. wink


Document ID:     tk0306-9  
Date:     2000/2/22 08:46:51  
Products Affected:     SmartSwitch Router, SSR, SSR2000, SSR2100, SSR8000, SSR8600  
Part Number(s):     SSR-CM-128, SSR-CM-64, SSR-CM2-128, SSR-CM2-64, SSR-RS-ENT  
 Revisions Affected:     1.0.0.0, 1.0.1.0, 1.1.0.0, 2.0.0.0, 2.1.0.0, 2.1.0.1, 2.2.0.0, 2.2.0.1, 2.2.2.0, 3.0.0.0, 3.0.0.2  
Product Families:     SmartSwitch Router  
Other Keywords:     ROUTER, SMARTSWITCH  
    

Overview
If the enable password for the SSR (SmartSwitch Router) is forgotten or misplaced, it will be necessary to perform enable recovery.
Discussion
To perform enable recovery on the SSR (SmartSwitch Router), the following steps may be used.
Manually reboot the SSR (SmartSwitch Router).

Press the key upon receiving the message, "Autoboot in 2 seconds - press ESC to abort and enter prom." (This message comes up quickly, so be prepared.)

Type "cp /int-flash/cfg/startup /int-flash/cfg/startup.sav", then press [return].

Type "rm /int-flash/cfg/startup", then press [return].

If the SSR is running 3.x or newer firmware, type "rm /pc-flash/startup", then press [return]. If not, then skip to the next step.

Type "reboot", then press [return].

After the SSR has completely booted up, type "enable", then press [return].

At the # prompt, type "copy startup.sav to scratchpad", then press [return].

Type "config", then press [return] for the configuration mode.

Type "show", then press [return].
.
Use the [spacebar] to scroll through the "scratchpad" configuration until you see the "system set hashed-password enable ..." (Note the appropriate line number in the left column.) Type "negate (number) scratchpad", then press [return].

Type "save active", then press [return].

Type "show", then press [return] again, to see that the old password has been removed. A new password may be entered using the "system set password enable (password)" command, then press [return].

Type "save active", then press [return] again to invoke the new password.

Type "save startup", then press [return] to provide the SSR with the newest startup configuration file. This action will also update any backup CM in the chassis.

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members!

Resources

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close