INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Jobs

CISCO AS5300

CISCO AS5300

(OP)
Has anyone ever tied an S8700 CM 2.0 to a CISCO AS5300 Universal Gateway? We are using the S8700 in conjunction with the AS5300 to provide PC dial in service to our LAN. I configured a TN464F as follows, ISDN-EXT/ESF/b8zs. Then a station as type DS1FD. The span will float but, when I call the assigned station it will ring but, no answer. Can someone point me in the right direction.

Gary L. Smith
Telephone Systems Engineer
The University of Mississippi
Telecommunications Department

RE: CISCO AS5300

(OP)
I've started over with the following setup...

I’m in need of some advice. My objective is to tie an S8700 to a CISCO AS5300 Gateway. It’s purpose is to allow employees off campus to connect to the Campus LAN (DIAL ACCESS). For on campus testing we are using x8901. In the AVAYA configuration below I can dial x8901 and terminates to a trunk group port. The call times out and I get reorder. I should get a BEEP and MODEM HANDSHAKE from the CISCO. I’ve never had an issue with building any type of T1. I’m just not sure if I’m routing x8901 correctly. Any advice would be appreciated. I’ve been hammering on this for 3 weeks now and I want to make sure that my end is at least 99% correct before I have to go to my network group to look at the CISCO setup.

ch vdn 8901                                                Page   1 of   2
                            VECTOR DIRECTORY NUMBER

                             Extension: 8901
                                  Name: REBEL NET
                         Vector Number: 5
                   Attendant Vectoring? n
                  Meet-me Conferencing? n
                    Allow VDN Override? n
                                   COR: 4
                                    TN: 1
                              Measured: none

change vector 5                                                 Page   1 of   3
                                  CALL VECTOR

    Number: 5                Name: REBEL NET
Multimedia? n      Attendant Vectoring? n    Meet-me Conf? n           Lock? n
     Basic? y   EAS? n   G3V4 Enhanced? n   ANI/II-Digits? n   ASAI Routing? y
 Prompting? y   LAI? n  G3V4 Adv Route? n   CINFO? n   BSR? n   Holidays? y
 Variables? n
01 route-to     number 050              with cov n if unconditionally

change trunk-group 1                                            Page   1 of  22
                                TRUNK GROUP

Group Number: 1                    Group Type: isdn          CDR Reports: y
  Group Name: DIAL IN SERV                COR: 93       TN: 1        TAC: 050
   Direction: two-way        Outgoing Display? y         Carrier Medium: PRI/BRI
 Dial Access? y                Busy Threshold: 255       Night Service:
Queue Length: 0
Service Type: tie                   Auth Code? n            TestCall ITC: rest
                         Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
         Codeset to Send Display: 6     Codeset to Send National IEs: 6
        Max Message Size to Send: 260   Charge Advice: none
  Supplementary Service Protocol: a     Digit Handling (in/out): enbloc/enbloc

            Trunk Hunt: cyclical                     QSIG Value-Added? n
                                                   Digital Loss Group: 13
Incoming Calling Number - Delete:     Insert:                 Format:
              Bit Rate: 1200         Synchronization: async    Duplex: full
 Disconnect Supervision - In? y  Out? n
 Answer Supervision Timeout: 0

TRUNK FEATURES
          ACA Assignment? n            Measured: none      Wideband Support? n
                                 Internal Alert? n        Maintenance Tests? y
                               Data Restriction? n     NCA-TSC Trunk Member:
                                      Send Name: n      Send Calling Number: y
            Used for DCS? n
   Suppress # Outpulsing? n    Format: public
 Outgoing Channel ID Encoding: preferred     UUI IE Treatment: service-provider

                                                 Replace Restricted Numbers? n
                                                Replace Unavailable Numbers? n
                                                      Send Connected Number: y
                                                  Hold/Unhold Notifications? y
             Send UUI IE? y                    Modify Tandem Calling Number? n
               Send UCID? y
 Send Codeset 6/7 LAI IE? y                         Ds1 Echo Cancellation? n

                                          US NI Delayed Calling Name Update? n

                     SBS? n  Network (Japan) Needs Connect Before Disconnect? N

                                TRUNK GROUP
                                      Administered Members (min/max):   1/10
GROUP MEMBER ASSIGNMENTS                  Total Administered Members:  10

       Port    Code Sfx Name        Night           Sig Grp
  1: 07E2001  TN464  F                                4
  2: 07E2002  TN464  F                                4
  3: 07E2003  TN464  F                                4
  4: 07E2004  TN464  F                                4
  5: 07E2005  TN464  F                                4
  6: 07E2006  TN464  F                                4
  7: 07E2007  TN464  F                                4
  8: 07E2008  TN464  F                                4
  9: 07E2009  TN464  F                                4
 10: 07E2010  TN464  F                                4

change ds1 07e20                                                Page   1 of   2
                                DS1 CIRCUIT PACK

            Location: 07E20                           Name: REBEL NET
            Bit Rate: 1.544                    Line Coding: b8zs
   Line Compensation: 1                       Framing Mode: esf
      Signaling Mode: isdn-pri
             Connect: line-side
   TN-C7 Long Timers? n                   Country Protocol: 1
Interworking Message: PROGress            Protocol Version: a
Interface Companding: mulaw                            CRC? n
           Idle Code: 11111111
                              DCP/Analog Bearer Capability: 3.1kHz

                                           T303 Timer(sec): 4


      Slip Detection? n                 Near-end CSU Type: integrated
                          Alarm When PRI Endpoint Detached? Y
                            DS1 CIRCUIT PACK

 ESF DATA LINK OPTIONS

                     Network Management Protocol: tabs
 Send ANSI-T1.403 One-Second Performance Reports? n
                             Far-end CSU Address: b

 INTEGRATED CSU OPTIONS
                                    Transmit LBO: 0db
                                    Receive ALBO: 26db
                                    Upon DTE LOS: loopback


 CPE LOOPBACK JACK OPTIONS
                  Supply CPE Loopback Jack Power? N

change signaling-group 4                                        Page   1 of   5
                                SIGNALING GROUP

 Group Number: 4              Group Type: isdn-pri
                    Associated Signaling? y          Max number of NCA TSC: 0
                       Primary D-Channel: 07E2024     Max number of CA TSC: 0
                                                   Trunk Group for NCA TSC:
       Trunk Group for Channel Selection: 1
          Supplementary Service Protocol: a

Gary L. Smith
Telephone Systems Engineer
The University of Mississippi
Telecommunications Department

RE: CISCO AS5300

Hi there, I was wondering if you found the solution to your problem. We are trying to do the same thing as you. We are replacing a Cisco AS5100 that has several external modems with a Cisco 3700 series router with digital modem ports which are accessed across a PRI trunk from our Avaya switch.

I'm on the network side of the house but I am familiar with the phone systems/switches. My telephone guys are fairly unfamiliar with the Avaya since our main switch-tech left. I was trying to figure out if you were able to get yours to work and if so what are your Avaya settings. Such as DSX settings, trunk group, signal group, and so forth.

He also says he doesnt know how to route/forward the calls to the trunk. It should be just one number for all the modems correct? I suppose that is what the vector directy numbers and call vector screens are for. Any help would be great.

Thanks,
Carl

RE: CISCO AS5300

(OP)
Hey Carl,

I've been through numerous amounts of documents from CISCO to AVAYA and all interoperability docs that I could get my hands on. From all the information that I could compile, it appears that you need a CO-Class switch that can provide SS7.

 We have everything working fine off of Bell South's 5ESS T1 but we would like to eliminate that and incorporate that into my switch to save a few dollars. I had everything hooked up, the span would float, the call would route to the span but, the CISCO would never answer. After a few months we decided that it wasn't worth wasting anymore time on.

Yes, a simple VDN with a vector that will route the call to the TAC of that trunk group will work fine. You may have a different choice of cards that you can put in the Cisco but, if you’re like me it’s up and running already so, I’m stuck with that. Good Luck!!!

Gary L. Smith
Telephone Systems Engineer
The University of Mississippi
Telecommunications Department

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members!

Resources

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close